At the same time, the commercial APC UPS works just fine under Ubuntu. However, when I plug it to Ubuntu 18.04 LTS, it is not working (not showing up in the Power settings).
Lsusb doesnt work windows 10#
When I connect it to Apple OSX (I'm using Macbook as a host machine) or Windows 10 VM machine, my "UPS" is correctly determined by the operating system and I can also report remaining battery capacity and other parameters back to the host. Kingston DataTraveler 102 Flash Drive / HEMA Flash Drive 2 GB / PNY Attache 4GB Stickīus 002 Device 003: ID 174c:1153 ASMedia Technology Inc.I'm developing a custom HID-compliant UPS based on Arduino Micro. Kingston DataTraveler 102 Flash Drive / HEMA Flash Drive 2 GB / P Attache 4GB Stickīus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hubīus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub ~ # vmware -vīus 001 Device 002: ID 0930:6545 Toshiba Corp. To load it while ESXi is running: ~ # vmkload_mod xhciĪfter setting the xHCI Mode to "Enabled" in the UEFI, both devices are connected to the USB 3.0 hub: ~ # vmware -vīus 002 Device 002: ID 174c:1153 ASMedia Technology Inc.īus 002 Device 004: ID 0bc2:5031 Seagate RSS LLC FreeAgent GoFlex USB 3.0īus 001 Device 002: ID 0930:6545 Toshiba Corp. To enable it (Load it automatically on boot): ~ # esxcli system module set -e true -m xhci If you do not see the USB 3.0 hub you have to verify that the xhci module is enabled and loaded with: ~ # esxcli system module list |grep xhci The problem described here applies only if you see a USB 3.0 root hub but devices are connected to the wrong hub. You can also use the lsusb -v command to see a verbose output containing the USB version (2.10): ~ # lsusb -vīDeviceClass 0 (Defined at Interface level) ~ # vmware -vīus 001 Device 008: ID 0bc2:5031 Seagate RSS LLC FreeAgent GoFlex USB 3.0īus 001 Device 007: ID 174c:1153 ASMedia Technology Inc. Kingston DataTraveler 102 Flash Drive / HEMA Flash Drive 2 GB / PNY Attache 4GB Stickīus 001 Device 002: ID 8087:8001 Intel Corp.īus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hubīus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hubīus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub USB 3.0 to mSATA SSD Enclosure (ASMedia Technology Inc.)īoth devices are connected to "Bus 001", which is the 2.0 root hub: ~ # vmware -vīus 001 Device 007: ID 0bc2:5031 Seagate RSS LLC FreeAgent GoFlex USB 3.0īus 001 Device 006: ID 174c:1153 ASMedia Technology Inc.īus 001 Device 003: ID 0930:6545 Toshiba Corp.External 1TB 2.5" HDD (Seagate RSS LLC FreeAgent GoFlex USB 3.0).After setting xHCI Mode to "Enabled", all devices are correctly identified as USB 3.0.ĭuring my tests I've use two USB 3.0 capable devices on my 5th Gen Intel NUC (NUC5i5MYHE):
Lsusb doesnt work drivers#
According to the documentation, in "Smart Auto" mode the USB 3.0 port acts like a 2.0 port before OS USB 3.0 drivers are loaded. For whatever reason, this does not work properly with ESXi. Within the UEFI the xHCI mode is configurable with a default of "Smart Auto". The solution was quite simple and not related to an ESXi, but to a UEFI configuration. This problem applies to both, USB devices in path-through mode, and USB devices mounted from the command line with usbarbitrator disabled. Unfortunately all of my devices are detected as USB 2.1, despite the USB 3 hub was visible. I know that USB 3.0, also known as eXtensible Host Controller Interface (xHCI), is supported in ESXi 6.0 and ESXi 5.5 Build 2143827 or later. In my latest post USB Devices as VMFS Datastore in vSphere ESXi 6.0 I had a problem with USB 3.0 devices that are detected as USB 2 in ESXi.
0 kommentar(er)
